LV SWITCH BOARDS
FOX design and
manufactures a range of Low Voltage switchboards to suit Client requirements.
Based on
market-leading modular construction systems, FOX manufactures a range of
partially & fully type-tested LV panels to customer requirements, with the
added advantage of quick turnaround from design to construction. All our panels
are in accordance with International standards and guarantees a quality
approved low voltage system.
FOX manufacture Main
and Sub-main distribution boards with ratings from 250A to 4000A in varying
forms of separation from Form 2 to Form 4 type 7, both fixed and fully
withdrawable.
Main
Distribution Board: The LV Panel/mains distribution
originates at the mains intake which is located next to the transformer and
radiates out throughout in a branching or tree like fashion.
Sub Main
Distribution Board: The Main Distribution board then feeds a Sub main
distribution board which is installed half way through the mains distribution
system, generally at the point where a large distribution cable terminates, and
several smaller sub-circuits start
Final
Distribution Board: The final distribution board is generally installed
locally to where the electrical power is used (point of utilization).
All FOX Factory-built
switchboard assemblies comply with the IEC 60-439 standard which defines the
service conditions, construction requirements, technical characteristics and
tests for low-voltage switchgear and control gear assemblies
Engineering
& Design
A complete system design and
application service is available from our specialist technical team, who are
always available to help and advice on any project.
Technical Knowledge
·
Designing of LV system projects and planning
·
Designing of
SLDs, GAs, Control Schematics & cable scheduling
·
Preparation of cable sizing and calculations,
and preparation of power & control cable schedules and loop diagrams
& termination diagrams.
· Preparation of Design Calculations for Busbar,
Heat Loss, Insulators, Lightning Protection, Lighting & Earthing &
Capacitor Banks.
· Design of motor starter feeders DOL, STAR-DELTA,
SOFT STARTERS and VFDs
· Short circuit & relay setting coordination
study for LV & MV systems
· Testing, Pre commissioning & Commissioning
· Preparation of Technical & material submittals
and documentation works.
· Job Estimations
In addition, our documented quality
systems ensure rigorous control of design, in-process inspection & testing,
component and assembly traceability, and final inspection & product
certification.
Project Engineering
· Professionally Qualified personnel’s with Good
working knowledge & experience in EPLAN, ELCAD and AutoCAD
· Planning and schedule preparation on MS-Projects
& Primavera software
·
Preparing the estimations using Siemens Software
- SIMARIS SIVACON 8PT & SIMARIS SIVACON S8.
FOX
guarantee
FOX can guarantee that the conformity of each Low Voltage switchboard
manufactured has been tested and proven. All our factory-built assemblies are:
· Made up of low-voltage devices and
components that all comply with the applicable international standards
· Based on protection & control
devices by leading suppliers:
o Siemens
o ABB
o Schneider
o L&T
· Based on recommended and proven
switchboard configurations
· Made up of Cubic system mechanical and
electrical components that have been subjected to the seven type-tests
required by IEC 60 439-1
· Assembled & wired by a competent and
trained panel builder
· Subjected to three routine tests
according to the IEC 60439-1 standard:
o Detailed
Inspection of the assembly
o Dielectric
test & electrical simulation testing
o Checking
of protective measures and of the electrical continuity of the protective
circuits
· Our systems are designed and built to
last, with particular attention to
o Ease
of installation on site
o Ease
of cabling access
o Ease
of client operation
o Accessibility
for planned maintenance
o Provision
for future expansion & extension
o Many
of our switchboards continue to perform and protect after three decades of service.
MOTOR CONTROL CENTRES
FOX’s MCC Panels
are designed as per the clients’ specifications & according to
international standards. The MCC panels are available with multiple power stabs
that help in supporting high capacity industrial motors. FOX MCC panels
comprises of Full voltage non-reversing and full voltage reversing starters, Variable
Frequency Drives, transformers, analog or digital metering, feeder fusible disconnects
and other features.
FOX manufactures a range of
Motor Control Centres with:
·
Forms of separation up to Form 4 type7
·
Built & tested to IEC 60 439-1
·
Comprehensive range of competitively
priced control gear from Siemens , ABB , Schneider and L&T
Types of MCC Panels:
· Conventional : Compartmental & Non Compartmental MCC
o Construction
from Form 1 through to Form 4
o Fixed
& Draw-out Construction
o Front
or rear access or a combination of both
o Incoming
cable entry can be top or bottom entry or a combination of both
o IEC
60439-1 compliant certified busbars and earth bars
o Fault
ratings: - 26 kA for 1 second, - 50 kA for 1 second, - 50 kA for 3 seconds, -
80 kA for 1 second
·
Intelligent MCC : MCC with Siemens (SIMOCODE) Products.
o Constructed
in compliance with the same standards as their Conventional MCC
o Built-in
pre-configured networks to allow engineers to access the full spectrum of data
available
o Provides
greater levels of diagnostic information for preventive maintenance
o Deliver
an array of operation and electrical information, including predictive alerts
that notify operators of problems
prior to system failures.
Engineering
& Design
A complete system design and
application service is available from our specialist technical team, who are
always available to help and advice on any project.
